Activate login mode at the Smart sun sensor (login at the Premium gateway) - Initial commissioning
General:
- The Smart sun sensor is supplied with a CR 2450 battery inserted. Carefully pull the separating foil out of the device. It is not necessary to open the device. Afterwards, all LEDs light up once briefly.
- The Smart sun sensor in combination with the Premium gateway has the function sun and vibration, both functions can be used as event in triggers.
- The sensitivities are set exclusively on the Smart sun sensor.
Registration at the Premium gateway:
The Smart sun sensor can either be registered directly with the 5 receivers for sun protection or with the Premium gateway. When registering with the Premium gateway, up to 100 devices can be controlled by the sensor via routines,
-
- Start the login mode on the Premium gateway via the app.
- Then press the menu button on the side of the sun sensor until the menu LED lights up blue.
- Tap the + button once, the status LED flashes green and switches to permanent green for a few seconds if the login was successful.
- The Smart sun sensor appears in the Premium gateway. You can define a name and optionally a description.
- If you would like to receive push messages via the Premium gateway for certain actions, you can activate this in the "Notifications" area.
Attach the sensor to the window:
-
- The Smart sun sensor is stuck relatively far down on the window pane. The sensor must not be covered later when a blind moves into the sun position. (if the sun function is used)
- The Smart sun sensor can be mounted vertically or horizontally.
- The operating buttons should be on the left or on top.
Use the sun function via the Premium gateway:
-
-
Set limit value
- There are two ways to set the sun sensitivity. The easiest way is to attach the sensor to the window pane and then accept the currently measured value as the limit value for the desired sun. To do this, press the menu button until the LED lights up yellow. Then press the Menu and Plus buttons simultaneously.
Alternatively, the sensitivity can be set manually in the sun menu. To do this, press the menu key until the LED lights up yellow and then simply press the plus or minus key until the desired value is displayed via the LEDs. The LEDs indicate 10 steps with 5 LEDs. If the LED flashes, it is half a step, if the LED lights up, it is a whole step. - A green status LED serves as a check. If the set limit value is below the currently measured value, the LED lights up green.
- There are two ways to set the sun sensitivity. The easiest way is to attach the sensor to the window pane and then accept the currently measured value as the limit value for the desired sun. To do this, press the menu button until the LED lights up yellow. Then press the Menu and Plus buttons simultaneously.
-
-
-
Create routine (Sun Start)
- Create a new routine
- Event Sun
- Selected device = Smart sun sensor
- Reaction to exceeded
- one-time event
- Add elements, you can select the devices individually or add an entire group.
- Set the appropriate target positions for the shutters to move to when the sun is shining. For example 40%.
-
-
-
Create routine (sun end)
- To make the shutters open again when the sun is no longer shining, create a second routine.
- Event Sun
- Selected device = Smart sun sensor
- Reaction to undershot
- one-time event
- Add elements that should be the same as those that were controlled with the sun start routine.
- Set the appropriate target position, which should be 0% for Sun End.
-
-
-
Test function
- Open all sunshades completely
- Press the menu button on the Smart sun sensor until the LED lights up yellow.
- Press the Plus and Minus keys simultaneously.
- All shutters move to the set sun positions
-
Use the vibration function via the Premium gateway:
-
-
Set limit value
- You can set the sensitivity for vibration manually in the vibration menu of the sensor. Tap the menu button until the LED lights up RED. Then simply tap the plus or minus key until the desired value is displayed via the LEDs. The LEDs show 10 steps with 5 LEDs. When the LED flashes it is a half step, when the LED is lit it is a full step.
-
-
-
Create a routine
- Create a routine
- Event "Shake
- Selected device = Smart sun sensor
- Reaction to vibration detected
- one-time event
- Optionally, a condition can be added. For example, a period from 10 pm to 6 am. This ensures that the alarm is not triggered if someone simply uses the window during the day.
-
-
-
- Add elements, you can select the devices individually or add an entire group.
- Set the appropriate target positions. For example: close the roller shutter, switch on the light.
-